Push/Pull Button to Turn ON/OFF LED via HAL

Lab Objective:

🔥 Requirements

Resources	Links
Computer	💻
ModusToolbox™ software v3.0 or later	Link
CY8CKIT-062S2-43012 Infineon Board	Link
Technical Report	dropbox

🚩 Let start

Create Application

• 👉 Open Eclipse IDE ModusToolbox

Select board and Application

Hardware Abstraction Layer (HAL) API

Open Hardware Abstraction Layer (HAL) API to see the functions that use for GPIO Pin

HAL API documentation

The HAL API documentation provides a comprehensive set of functions to interact with the board efficiently. This API documentation offers detailed guidance on utilizing various functionalities to optimize your development process.

Coding

• Coding: Open the main.c file and add the following code to the main(void) function.

int main(void)
{
    cy_rslt_t result;

    /* Initialize the device and board peripherals */
    result = cybsp_init() ;
    /*BSP init failed. Stop program execution */
    if (result != CY_RSLT_SUCCESS)
    {
        CY_ASSERT(0);
    }
    __enable_irq();


    /* Initialize the User LED */
    cyhal_gpio_init(CYBSP_USER_LED, CYHAL_GPIO_DIR_OUTPUT, CYHAL_GPIO_DRIVE_STRONG, CYBSP_LED_STATE_ON);

    /* Initialize the user button */
    cyhal_gpio_init(CYBSP_USER_BTN, CYHAL_GPIO_DIR_INPUT, CYHAL_GPIO_DRIVE_PULLDOWN, CYBSP_BTN_OFF);

    /* Initialize retarget-io to use the debug UART port. It sets up the standard input/output functions (such as printf)*/
    cy_retarget_io_init(CYBSP_DEBUG_UART_TX, CYBSP_DEBUG_UART_RX, CY_RETARGET_IO_BAUDRATE);

    printf("\x1b[2J\x1b[;H");

    for (;;)
    {
    	//Button is active low
    	if(!cyhal_gpio_read(CYBSP_USER_BTN)){
            // Button is pressed
            cyhal_gpio_write(CYBSP_USER_LED, CYBSP_LED_STATE_ON);
            printf("Button Pressed --> LED ON \r\n");
            cyhal_system_delay_ms(250);
        }

        else {
            // Button is not pressed
            cyhal_gpio_write(CYBSP_USER_LED, CYBSP_LED_STATE_OFF);
            printf("Button not Pressed --> LED OFF \r\n");
            cyhal_system_delay_ms(250);
        }
    }
}

Here is the sample functions that we use from the HAL API documentation

Build the Application

• 👉 Build the Application

Launching the Application

• 👉 Launching the Application

  • Before launching the program to the board, make sure that you have already connected the board to the computer through a USB cable.

    

    set up USB cable
  • Launching Program

  
• 👉 Check the Result

🎉 Congratulations! You can now complete Lab103

Supported toolchains (make variable 'TOOLCHAIN')

• GNU Arm® embedded compiler v10.3.1 (GCC_ARM) - Default value of TOOLCHAIN

• Arm® compiler v6.16 (ARM)

• IAR C/C++ compiler v9.30.1 (IAR)

Supported kits (make variable 'TARGET')

• PSoC™ 62S2 Wi-Fi Bluetooth® pioneer kit (CY8CKIT-062S2-43012)

• PSoC™ 62S1 Wi-Fi Bluetooth® pioneer kit (CYW9P62S1-43438EVB-01)

• PSoC™ 62S1 Wi-Fi Bluetooth® pioneer kit (CYW9P62S1-43012EVB-01)

• PSoC™ 62S3 Wi-Fi Bluetooth® prototyping kit (CY8CPROTO-062S3-4343W)

Related resources

Resources	Links
ModusToolbox™ Software Training	link

Other resources

Infineon provides a wealth of data at www.infineon.com to help you select the right device, and quickly and effectively integrate it into your design.

Document history

Document title: BILL_MTB-103 – GPIO-HAL Button with LED Template

Version	Description of change
1.0.0	Lab 103: Learn basic GPIO control with PSoC 6 using Push/Pull Button to Turn ON/OFF LED via HAL

Authors:

• Assoc. Prof. Wiroon Sriborrirux

• Mr. Sriengchhun Chheang

• Mr. Sabol Socare

---

© BDH Corporation, 2022-2023